2016 Mazda MAZDA3 Technical Service Bulletins

667 technical service bulletins (TSBs) are on record for the 2016 Mazda MAZDA3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10136371Feb 22, 2018Electrical system. Some vehicles may exhibit the active driving display opening/closing improperly as described below: It does not open or close when the ignition is turned ON or OFF. The display operation does not fully open/close. It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the active driving display which activates pinching detection.
• 10136368Feb 22, 2018Electrical system. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To…
• 10136325Feb 22, 2018Fuel system, Engine cooling. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine…
• 10134920Feb 20, 2018Equipment. Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.
• 10134925Feb 16, 2018Air bags, Equipment. The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
• 10134921Feb 16, 2018Equipment. The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.
• 10136370Feb 14, 2018Equipment, Electrical system. Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.
• 10136326Feb 13, 2018Wheels. Some vehicles may exhibit an aluminum alloy type wheel(s) having one of the following paint damage conditions shown in the sample photos below. The damage extends to the front surface of the aluminum wheel partly or entirely. Black Spot White Spot Flaking / Peeling Discolored Blackened.
• 10134924Feb 9, 2018Electrical system. Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound
• 10134917Feb 8, 2018Equipment. Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition.
• 10136369Feb 6, 2018Body and structure. Some vehicles may exhibit rust/paint blisters (1) on the surface of the front side sill near the the scuff plates(2). This is likely caused by the driver's or passenger's shoe(s) contacting the side sill when stepping in and/or out of the vehicle since the side sill of the Mazda3 is wider than other models. When this happens, mud/sand stuck to the sole of the shoe scratches the paint surface, which then develops…
• 10129574Jan 29, 2018Seats. Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction…
• 10129565Jan 8, 2018Equipment. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD…
• 10129563Jan 5, 2018Suspension. Some vehicles may exhibit one or more of the following noises from the front suspension. A squeaking noise from the front shock absorber when turning the steering wheel at a vehicle standstill caused by stick-slip between the front strut bearing and the coil spring. A popping noise from the front shock absorber when passing over speed bumps caused by the bump stopper contacting the strut bearing when the shock…
• 10129353Jan 4, 2018Equipment. The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
• 10129354Jan 2, 2018Electrical system. When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.
• 10129327Dec 18, 2017Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10129368Dec 5, 2017Equipment, Engine. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
• 10188490Nov 9, 2017Electrical system, Equipment, Brakes. WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot perform any additional testing of the system. Dealers and customers should never attempt to test or recreate crash scenarios under any circumstances because that could lead to an…
• 10188480Nov 9, 2017Electrical system, Equipment. Some customers may experience a MAZDA CONNECT touch panel that does not accept touch commands properly or operates by itself. This is caused by a touch panel failure from an improper manufacturing process of the touch panel and center display integration.
• 10188488Nov 2, 2017Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10188479Nov 1, 2017Equipment, Visibility (wipers, defrost, mirrors), Body and structure. Some vehicles may exhibit white stains (A) running down the front door(s) from the base of the outer mirror, causing a poor appearance. This is caused when water enters the mirror base and corrodes the aluminum die cast inside the mirror. To eliminate the concern, the aluminum die cast inside the mirror base has been painted to prevent corrosion.
• 10125469Oct 18, 2017Forward collision avoidance. The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is…
• 10123436Oct 3, 2017Equipment. Some vehicles may experience unusual noise coming from inside the front door panel when playing the audio system. This is caused by the damper coming off the speaker frame due to corrosion. To correct the issue, a plating process was added at the supplier beginning on November 13, 2015.
• 10118754Sep 13, 2017Electrical system, Equipment. IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.
• 10120387Sep 11, 2017Body and structure. Some vehicles may exhibit paint rust/blister on the vertical surface of the trunk lid. This is caused by silica contained in snow-melting agents adhering to the trunk lid. To correct this issue, the thickness of the clear coat has been increased.
• 10120384Sep 8, 2017Equipment. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. For Mazda6 and CX-5, the check engine light may illuminate with the DTC P011A:00 stored at the same time. P011A:00 ECT sensor No.1/No.2 performance problem. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing.
• 10118751Sep 1, 2017Exterior lighting, Forward collision avoidance. Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
• 10118476Aug 25, 2017Engine. If a customer brings their vehicles in with DTC P2183:00 stored, repair the vehicle using the following Repair Procedure and Caution. P2183:00: ECT sensor No.2 circuit range/performance problem. This is caused by the ECT sensor No.2 located near the bottom of the radiator getting wet and water entering the part due to insufficient water resistance. To correct this issue, the water resistance of the ECT sensor No.2…
• 10118473Aug 24, 2017Equipment, Electrical system. This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17).
• 10118472Aug 23, 2017Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10118471Aug 22, 2017Steering, Suspension. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. NOTE: The noise will not occur if the steering wheel is in the center or full right position. The noise is caused when the edge (A) of the left side inner ball joint (B) gets stuck with the steering gear…
• 10118470Aug 11, 2017Brakes. Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (A) on the front disc plates. This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used.
• 10118479Aug 10, 2017Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth®, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command
• 10118468Aug 9, 2017Body and structure, Electrical system, Exterior lighting. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No.
• 10118467Aug 7, 2017Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10118463Aug 4, 2017Equipment, Body and structure. Some vehicles may experience unusual noise coming from inside the front door panel when playing the audio system. This is caused by the damper coming off the speaker frame due to corrosion on the speaker back frame. To correct the issue, a plating process was added at the supplier beginning on November 13, 2015.
• 10118462Aug 4, 2017Engine, Electrical system. If a customer brings their vehicles in with DTC P2183:00 stored, repair the vehicle using the following Repair Procedure and Caution. P2183:00: ECT sensor No.2 circuit range/performance problem. This is caused by the ECT sensor No.2 located near the bottom of the radiator getting wet and water entering the part due to insufficient water resistance. To correct this issue, the water resistance of the ECT sensor No.2…
• 10111043Jul 26, 2017Equipment. Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
• 10120378Jul 24, 2017Equipment. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine…
• 10120376Jul 21, 2017Brakes. Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (A) on the front disc plates. This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used.
• 10111038Jul 21, 2017Equipment, Electrical system. Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.
• 10120374Jul 12, 2017Visibility (wipers, defrost, mirrors). Some vehicles may experience one or more of the following conditions with the driver and/or passenger side power window(s): ? The window glass will not raise/lower. The window suddenly stops operating while being raised/lowered. The window glass gets stuck where it stopped operating or falls down in the door. This concern is caused by the window regulator cable end becoming disconnected from the fixing point due to…
• 10120373Jul 12, 2017Electrical system. All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later).
• 10111036Jul 12, 2017Electrical system. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is© 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.
• 10111035Jul 12, 2017Transmission and drivetrain, Engine, Electrical system. Some 2012-2016 Mazda3s, 2013-2015 CX-5s and 2014-2015 Mazda6s may experience the Check Engine Light ON with DTC P0101 and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. If the PCM is reprogrammed with any software number included in the attached file and the throttle valve has too much carbon build up, the engine air amount calculation by the problem software…
• 10120372Jul 6, 2017Steering. Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
• 10111042Jul 6, 2017Electrical system, Transmission and drivetrain. Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging.
• 10111034Jul 6, 2017Visibility (wipers, defrost, mirrors). CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.
• 10111033Jul 6, 2017Exterior lighting. High Beam Control (HBC) system frequently asked questions (FAQ)

← All problems reported for the 2016 Mazda MAZDA3