2017 Mazda MAZDA6 Technical Service Bulletins

516 technical service bulletins (TSBs) are on record for the 2017 Mazda MAZDA6. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10134698Mar 22, 2018Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.
• 10134934Mar 20, 2018Fuel system. The SKYACTIV®-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV® oil filters. The unique oil filter can be identified with two white bands as shown below.
• 10134694Mar 19, 2018Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10134691Mar 9, 2018Engine, Engine cooling. When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire…
• 10134932Mar 5, 2018Equipment. When installing a navigation SD card, the center display may show error message "Invalid SD Card".
• 10134690Mar 5, 2018Equipment. Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
• 10136368Feb 22, 2018Electrical system. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during extremely cold temperatures. To…
• 10136325Feb 22, 2018Engine cooling, Fuel system. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine…
• 10134920Feb 20, 2018Equipment. Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display.
• 10134925Feb 16, 2018Equipment, Air bags. The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
• 10134921Feb 16, 2018Equipment. The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Navigation SD Card Map Update Note: Mazda Toolbox navigation SD card map update can only be performed on a navigation SD card that is VIN-locked. See VIN-lock procecure below.
• 10136370Feb 14, 2018Equipment, Electrical system. Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.
• 10136326Feb 13, 2018Wheels. Some vehicles may exhibit an aluminum alloy type wheel(s) having one of the following paint damage conditions shown in the sample photos below. The damage extends to the front surface of the aluminum wheel partly or entirely. Black Spot White Spot Flaking / Peeling Discolored Blackened.
• 10134924Feb 9, 2018Electrical system. Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and the same device is also connected to the USB port for charging. The concerns may include: Blank Screen and/or No Audio Sound, Phone will not charge, Blank Screen and/or No Audio Sound
• 10134917Feb 8, 2018Equipment. Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition.
• 10129574Jan 29, 2018Seats. Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction…
• 10129571Jan 18, 2018Forward collision avoidance. Some customers may experience the following symptom relating to the Forward Sensing Camera (FSC)with DTC C1001:92 [Forward sensing camera (FSC) poor field of view] stored in memory.When the visibility out the windshieldis poor (i.e. fog or raining at night), the following warning lights mayilluminate.
• 10129569Jan 16, 2018Electrical system. Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. The SD card has been updated to eliminate this concern.
• 10129567Jan 10, 2018Electrical system. Some customers may complain that the Voice Recognition system does not recognize "Address" or "NewDestination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
• 10129566Jan 9, 2018Electrical system. After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters.
• 10129565Jan 8, 2018Equipment. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD…
• 10129564Jan 5, 2018Suspension. Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the…
• 10129353Jan 4, 2018Equipment. The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
• 10129354Jan 2, 2018Electrical system. When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.
• 10129351Dec 22, 2017Electrical system. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction.
• 10129327Dec 18, 2017Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10129368Dec 5, 2017Engine, Equipment. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
• 10188485Nov 17, 2017Visibility (wipers, defrost, mirrors), Body and structure. Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been…
• 10188482Nov 13, 2017Equipment, Electrical system, Seats. Some vehicles may exhibit excessive noise when operating either front power seat forward or backward. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the case due to inadequate fabric wrapped around the cable. The fabric thickness has been increased to eliminate the noise.
• 10188491Nov 9, 2017Electrical system. The MODE switch operation for the Mazda Radar Cruise Control (MRCC) system has been changed as follows: Previous - Press the MODE switch to switch to the cruise control function. New - Press the MODE switch and hold for 2 seconds_ to switch to the cruise control function.
• 10188488Nov 2, 2017Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10123444Oct 27, 2017Electrical system, Exterior lighting. Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area.? Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been…
• 10125469Oct 18, 2017Forward collision avoidance. The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is…
• 10123440Oct 9, 2017Electrical system, Visibility (wipers, defrost, mirrors). Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.
• 10123439Oct 6, 2017Brakes, Back-over prevention (rear camera), Electrical system. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction.
• 10118754Sep 13, 2017Equipment, Electrical system. IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.
• 10118752Sep 12, 2017Visibility (wipers, defrost, mirrors), Equipment, Electrical system. Due to a change in the 2017 Mazda3, Mazda6 and 2018 CX-9 A-pillar wiring harness, the EC Mirror w/compass / EC Mirror w/compass + Homelink installation instructions have been updated.
• 10120386Sep 8, 2017Exterior lighting, Lane departure. Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. At that time, the windshield is clear but the lens of the Forward Sensing Camera (FSC) is foggy. The FSC may not function properly under the following conditions: ? Foggy windshield ? Foggy FSC lens ? Heavy rain, dense…
• 10120384Sep 8, 2017Equipment. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. For Mazda6 and CX-5, the check engine light may illuminate with the DTC P011A:00 stored at the same time. P011A:00 ECT sensor No.1/No.2 performance problem. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing.
• 10118751Sep 1, 2017Forward collision avoidance, Exterior lighting. Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
• 10118477Aug 29, 2017Steering, Electrical system, Suspension. Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6). Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6). The bump stopper (C) may be contacting the strut bearing when…
• 10118474Aug 24, 2017Exterior lighting, Lane departure. Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. At that time, the windshield is clear but the lens of the Forward Sensing Camera (FSC) is foggy. The FSC may not function properly under the following conditions: ? Foggy windshield ? Foggy FSC lens ? Heavy rain, dense…
• 10118473Aug 24, 2017Electrical system, Equipment. This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17).
• 10118472Aug 23, 2017Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10118471Aug 22, 2017Suspension, Steering. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. NOTE: The noise will not occur if the steering wheel is in the center or full right position. The noise is caused when the edge (A) of the left side inner ball joint (B) gets stuck with the steering gear…
• 10118480Aug 18, 2017Electrical system, Exterior lighting. Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Instrument Cluster Multi-Information Display warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction.
• 10118479Aug 10, 2017Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth®, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command
• 10118468Aug 9, 2017Exterior lighting, Electrical system, Body and structure. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No.
• 10118467Aug 7, 2017Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10118466Aug 4, 2017Lane departure, Electrical system, Visibility (wipers, defrost, mirrors). Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

← All problems reported for the 2017 Mazda MAZDA6