2019 Mercedes-Benz Sprinter 1500 Technical Service Bulletins

159 technical service bulletins (TSBs) are on record for the 2019 Mercedes-Benz Sprinter 1500. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 11038169Sep 29, 2026Brakes. Brakes may lock up when reversing at slow speeds Complaint When reversing slowly, the vehicle erroneously triggers an emergency braking event, causing the brakes to lock up. Engine may not start following a key cycle. Cause The vehicle triggers a maneuvering or emergency braking event while reversing. The customer must then immediately park the vehicle (ignition Switched OFF) The hydraulic pressure release process…
• 11038718Sep 26, 2026Other or unknown. Fuel Level Unchanged After Refueling Complaint The customer reports that the fuel gauge shows inaccurate readings or remains unchanged after refueling. Cause The fuel level display may be incorrect due to one or both of the following conditions: 1. The Fuel Supply Control Unit (FSCU) may not recognize a refueling event if the Controller Area Network (CAN) does not enter sleep mode.
• 11038168Sep 25, 2026Transmission and drivetrain. Sprinter 907 with 725.0 (NAG3 Classic) Transmission ‑ Shudder during acceleration Complaint Shudder may be felt in the following situations: • accelerating from stop or up hill • during upshifts Cause Under Investigation, possible torque converter clutch operation
• 11038170Sep 19, 2026Other or unknown. Unavailability of MB Apps Complaint A popup is seen on the HU with the message "data connection temporarily not available". Cause MB Apps is officially sundowned for all vehicles with NTG5 Head Unit Variant. Remedy No support available for NTG5 Head Unit Variants for MB App related topics.
• 11036855Aug 26, 2026Transmission and drivetrain. Complaint While driving through muddy / sandy/ off road terrain "4Matic Currently Unavailable" message on the dash Cause This vehicle is not equipped with a fixed force distribution AWD, rather force is only applied to the front axle according to ESP calculations. As per GF28.00‑D‑ 9900A: "vehicles with 4MATIC all‑wheel system and variable force distribution, an electronically regulated multiplate clutch integrated…
• 11035562Jul 17, 2026Transmission and drivetrain. Model 907 with all-wheel drive (A4M) – All-wheel drive inoperative Complaint The customer may report one or more of the following: • All-wheel drive is unavailable or inoperative. • Rear wheel slip during acceleration on low-traction surfaces. • Noise from the front axle area while driving. • Message in the instrument cluster indicating all-wheel drive is unavailable due to overheating. • Fault code P27874B - The…
• 11035563Jul 1, 2026Other or unknown. ASSYST PLUS service reminder appears earlier than expected due to vehicle operating conditions Complaint The ASSYST PLUS service reminder appears earlier than expected. The customer or dealer may report that the vehicle did not reach the starting maintenance interval shown in vehicle documentation, option coding, sales literature, or the Owner's Manual.
• 11034410Jun 15, 2026Transmission and drivetrain. Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes…
• 11030629Mar 23, 2026Fuel system. The check engine light is illuminated, or the AdBlue warning is active, with recorded faults related to AdBlue quality or concentration. Complaint Customer reports an illuminated check engine light and or an AdBlue system warning indicating AdBlue quality out of specification. The vehicle may enter reduced performance mode. One or more of the following fault codes related to the AdBlue tank may be stored: P206B31…
• 11029272Feb 24, 2026Engine. Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset with fault code P13DF00 or P300685 Complaint Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset. Information: All fault codes in the AdBlue® (SCR) control unit have been processed and corrected; however, fault codes P13DF00 and P300685 remain active and stored in the AdBlue® (SCR) control unit.
• 11028113Jan 16, 2026Engine. EGR Valve Diagnosis & Cleaning (and EGR Cooler Cleaning) – OM642, Sprinter 906/907 Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also…
• 11028119Jan 15, 2026Engine. Complaint Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset. Information: All fault codes in the AdBlue® (SCR) control unit have been processed and corrected; however, fault codes P13DF00 and P300685 remain active and stored in the AdBlue® (SCR) control unit. Cause The procedure for resetting the SCR/AdBlue® warning message with XENTRY Diagnosis has not been carried out.
• 11024928Oct 6, 2025Other or unknown. The software for the communication module does not correspond to the latest series production configuration. For this reason, a remote software update to update the software for the communication module is planned for the affected vehicles. This update includes quality-enhancing optimizations for the communication module to improve the system stability and accessibility of connected services. MBUSA is conducting a…
• 11023983Sep 26, 2025Other or unknown. Engine Oil Level Cannot Be Checked via Instrument Cluster Service Menu Complaint Sometimes the engine oil level cannot be determined using the instrument cluster's service menu. The following mes- sages may be displayed: •Engine oil level currently inoperative. See Attachment: Message "Engine oil level currently inoperative" (shown in German on model 907 with code C6L (Multifunction steering wheel)). •Engine oil…
• 11023982Sep 16, 2025Transmission and drivetrain. Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4…
• 11023975Sep 4, 2025Electrical system. MBAG has determined the software of the control unit for the anti-theft warning system does not correspond to the current production configuration. There is a possibility that the alarm system (EDW) could be triggered while the vehicle is parked and locked. MBUSA is conducting a service campaign. An authorized Mercedes-Benz Sprinter dealer will update the anti-theft system software on the affected vehicles.
• 11022498Aug 12, 2025Other or unknown. Mercedes-Benz AG, the manufacturer of Mercedes-Benz Sprinter vans, has determined that on certain Model Years 2017-2021 Sprinter vehicles, the In Use Monitor Performance Ratio (“IUMPR”) function of the OBD system might not perform as intended under certain circumstances.
• 11018922May 19, 2025Engine. Complaint The check engine light is activated, accompanied by one or more of the following fault codes related to the Adblue System: •P20F409: The Adblue consumption is too low. There is a component fault. •P202E84: The Adblue metering valve 1 (Motor side) has a malfunction. There is a signal below the permissible limit value. Cause The potential causes for these fault codes are: A. A leak in the Adblue System B…
• 11018921May 19, 2025Engine. Complaint The check engine light is activated, accompanied by the following fault code related to the Exhaust gas recirculation cooler (low pressure): •P300E55 The efficiency of component 'Exhaust gas recirculation cooler (low pressure)' is not sufficient. Cause The issue is attributed to an error in the coding of the climate control unit software (HVAC177). Remedy A software update to correct the coding error is…
• 11018920May 9, 2025Engine. Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes…
• 11017570Apr 25, 2025Engine. In our continuing efforts to assure the proper performance of our products and to ensure the satisfaction of our customers, the warranty for the EGR Valve in the vehicles listed below has been extended from the original 5 years/100,000 miles to 15 years/150,000 miles, whichever occurs first.
• 11017565Apr 25, 2025Engine. EGR Valve Diagnosis and Cleaning Procedure using TUNAP 926® on 906, 907 Sprinter with OM642 Diesel Engine Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault…
• 11017558Apr 3, 2025Engine. Check engine light illuminated - Fault code current P04D-B79 The crankcase ventilation system is interrupted. Complaint: Check engine light on. Fault code P04DB79 is current in the engine control module (N3/10). Cause: Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for S208 vent line contact switch. Refer to attached photo of connection location. 2. Ensure…
• 11016429Mar 18, 2025Fuel system. Check engine light or Adblue warning with fault codes P206B31, P203B31, or P300494 when outside temperatures are below 32 degrees Fahrenheit. SCR Gen4 (KP7) Complaint: The check engine light or AdBlue warning is activated, accompanied by one or more of the following fault codes rela- ted to the AdBlue tank: P206B31: Malfunction of the concentration sensor for AdBlue; the signal is absent. P203B31: Malfunction of…
• 11016430Mar 10, 2025Visibility (wipers, defrost, mirrors). Warning Lamp "Washer Fluid Empty" Yet Reservoir Is Not Empty Complaint: Warning lamp "washer fluid empty", even thought the washer fluid reservoir is full Cause: Insufficient electrical conductivity of the washer fluid, as the washer fluid was mixed with distilled water. Tip: The washer fluid sensor detects the electrical conductivity. If air is present without electrical conductivity between the measuring points…
• 11016427Mar 10, 2025Fuel system. Procedure for When Diesel Fuel Tank is Filled with Incorrect Fuel Type Complaint: Procedure for When Diesel Fuel Tank is Filled with Incorrect Fuel Type (e.g., gasoline, water, biodiesel, AdBlue/DEF) Cause: The incorrect fuel type, such as gasoline, water, biodiesel, or AdBlue/DEF has been added to the fuel system.
• 11016426Mar 10, 2025Fuel system. Fuel Level Unchanged After Refueling Complaint: The customer reports that the fuel gauge shows inaccurate readings or remains unchanged after refueling. Cause: A. The FSCU fails to detect a refueling event. B. The Fuel Level Sensor provides incorrect readings.
• 11016423Mar 10, 2025Fuel system. EGR Valve Diagnosis and Cleaning Procedure Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review…
• 11016428Mar 6, 2025Engine. Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset with fault code P13DF00 or P300685 Complaint: Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset. Information: All fault codes in the AdBlue® (SCR) control unit have been processed and corrected; however, fault codes P13DF00 and P300685 remain active and stored in the AdBlue® (SCR) control unit.
• 11014726Feb 12, 2025Fuel system. Complaint Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Cause Various causes Remedy Up to Model year 2018: Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the gui- ded test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is…
• 11013888Feb 6, 2025Engine. Check engine light on and FC P146264 stored in engine and fuel pump control units
• 11013887Feb 6, 2025Engine. M274 poly-V belt squeaking noises, falls off, not aligned, broken
• 11014728Feb 4, 2025Fuel system. Complaint The check engine light or AdBlue warning is activated, accompanied by one or more of the following fault codes rela- ted to the AdBlue tank: P206B31: Malfunction of the concentration sensor for AdBlue; the signal is absent. P203B31: Malfunction of the AdBlue fill level sensor; the signal is absent. P300494: The quality of the AdBlue is insufficient. Cause A. The software for the AdBlue (SCR) control unit…
• 11011223Nov 28, 2024Engine. SMOG/Emissions Test fail due to one or more Readiness Monitors not set Complaint: The vehicle has failed the State Emissions Certification because one or more of the OBDII readiness monitors are not completely set.
• 11009854Oct 25, 2024Transmission and drivetrain. Complaint: Noises when reversing slowly <5 km/h (squeaking) Cause: There is a seal in the electric drivetrain that seals off the coolant system from the electric motor. This seal is moistened with coolant during forward travel. As a result of the change in rotational direction when reversing slowly, it may be the case that this sealing ring is no longer moistened. Squeaking noises may occur as a result of the…
• 11009856Oct 17, 2024Other or unknown. Complaint: Check engine light with fault code: P300E3B the efficiency of component 'SCR catalytic converter' is not sufficient, is present in the CDI control unit CDI (N3/28). Cause: This subject is currently being analyzed for all 907s equipped with the OM642 engine. Follow the instructions related to this subject to collect information about your vehicle. After completing the checks, please open a TIPS case and…
• 11008717Sep 25, 2024Other or unknown. Complaint Check engine light with fault code: P300E3B the efficiency of component 'SCR catalytic converter' is not sufficient, is present in the CDI control unit CDI (N3/28). Cause This subject is currently being analyzed for all 907s equipped with the OM642 engine. Follow the instructions related to this subject to collect information about your vehicle. After completing the checks, please open a TIPS case and…
• 11005573Jul 4, 2024Engine. Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document…
• 11001110May 8, 2024Body and structure. Complaint: Front door collides with fender. Excessive dynamic stress results in permanent deformation of the lower hinge and causes the front door to collide with the fender. This can result in damage to the door holder and the front door at the threaded connection of the door holder. Remedy: 1. In the event of damage to be claimed under warranty, please follow warranty guidelines 10.11.1 (see note) 2.
• 10253244Mar 1, 2024Transmission and drivetrain. Propeller Shaft Check Strap on the crossmember may not have been installed.
• 10251998Feb 1, 2024Equipment. News channel update.
• 10251997Feb 1, 2024Equipment. News channel update.
• 10251090Jan 18, 2024Body and structure. Check Par????on Wall Bolts
• 10251088Jan 4, 2024Equipment. Recall Information.
• 10251085Jan 3, 2024Body and structure. Check patrition Wall Bolts
• 10240168Jul 13, 2023Steering. Various concerns in relation to electric power steering including Rattling/humming noise from electric power steering when steering fully turned (see video recordings 01 and 02).
• 10240045Jun 6, 2023Engine cooling, Electrical system. Modify Interior Blower Motor Fuse Layout
• 10237246May 8, 2023Electrical system. Complaint Some MY2019 Amazon Sprinters have a customer-specific 'Driver Alert' Parameterizable Special Module (PSM) software that monitors signals from multiple sensors and outputs audible and visual feedback if the proper parking procedure has not been performed by the driver. This customer-specific software was developed and approved by Mercedes-Benz and Amazon to enhance driver and pedestrian safety based on…
• 10233787Mar 8, 2023Fuel system, Engine cooling. Complaint Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset. Information: All fault codes in AdBlue® (SCR) control unit have been processed and rectified; however fault code P13DF00 remains active and stored in the AdBlue® (SCR) control unit. Cause The procedure for resetting the SCR/AdBlue® warning message with XENTRY Diagnosis has not been carried out.
• 10233790Mar 1, 2023Body and structure. Complaint Noise in front door from window regulator when driving. Cause Loosened nut of window lifter leads to screw connection at bottom of door breaking the mounting point in the door (see attached picture). Remedy Glue in repair panel A 910 722 33 00 and screw in again with collar nut A 005 990 64 50. When using the adhesive, observe the following: Roughen the bonding surfaces slightly and clean them so that…

← All problems reported for the 2019 Mercedes-Benz Sprinter 1500