2013 Audi A3 Technical Service Bulletins

864 technical service bulletins (TSBs) are on record for the 2013 Audi A3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10128429Aug 5, 2015Engine cooling, Visibility (wipers, defrost, mirrors). This document contians the dealer letter that provides information on the 19L2 service action that wil be turned back on for Elsa visibility on or about August 06, 2015. Customer notification will begin on or about August 31, 2015.
• 10128498Jul 21, 2015Engine cooling. The coolant pump may develop a small leak over time. Inspect and, if necessary, replace the coolant pump.
• 10058670Jul 21, 2015Engine cooling. Audi: tsb contains an owner notification letter. Select document search button below. On some vehicles, overtime a small leak will develop in the coolant pump and pump will need to be inspected and if necessary, replaced. Model 2010-13 a3.
• 10128484Jul 20, 2015Engine cooling. This document contains information on the upcoming service action 19L2 for the coolant pump.
• 10128399Jul 7, 2015Engine cooling. Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
• 10128471Jul 1, 2015Transmission and drivetrain, Equipment. Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in…
• 10128469Jul 1, 2015Engine, Electrical system. The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.
• 10122578Jul 1, 2015Fuel system. This document contains the dealer letter in regards to 2009-2015 model year Audi TDI® clean diesel vehicles registered in Minnesota engine codes CBEA, CATA, CNRB, CPNA, CPNB using biodiesel blend fuels.
• 10122577Jul 1, 2015Fuel system. This document contains the customer letter in regards to 2009-2015 model year Audi TDI® clean diesel vehicles registered in Minnesota engine codes CBEA, CATA, CNRB, CPNA, CPNB using biodiesel blend fuels.
• 10058584Jul 1, 2015Engine. Audi: engine, on some vehicles, would run irregularly or have malfunction indicator lamp (mil) on or possible filter element for camshaft adjustment valve can loosen and in oil circuit, there is no damage from loosened particles. Model all. All years.
• 10120811Jun 30, 2015Fuel system. Supersedes Technical Service Bulletin Group 01 number 14-75 dated March 20, 2014. The MIL is on. No start or rough running. One or more DTCs are stored in the engine control module. When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for…
• 10058586Jun 30, 2015Engine cooling. Audi: some vehicles will experience rough running or a no start condition with malfunction indicator lamp (mil) on and may need checking high pressure fuel pump for metallic particles. Model 2013-2016 a3, a8, q5, 17.
• 10120832Jun 29, 2015Electrical system. Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises.
• 10120821Jun 24, 2015Equipment. Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
• 10120829Jun 19, 2015Electrical system. The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
• 10120904Jun 15, 2015Transmission and drivetrain, Brakes, Equipment, Engine cooling, Steering. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service.
• 10120743Jun 9, 2015Engine cooling. The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM.
• 10120805Jun 2, 2015Engine. Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
• 10120052May 29, 2015Electrical system. Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
• 10120050May 21, 2015Exterior lighting. Supersedes Technical Service Bulletin Group 94 number 12-96 dated November 1, 2012. Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. For vehicles with halogen daytime running lights, refer to TSB 2017488: 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip…
• 10120048May 19, 2015Equipment. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded.
• 10120041May 18, 2015Equipment. Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
• 10120043May 8, 2015Equipment, Electrical system. Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814.
• 10120049May 1, 2015Visibility (wipers, defrost, mirrors). Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the…
• 10120002Apr 24, 2015Back-over prevention (rear camera), Equipment. Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off.
• 10120004Apr 17, 2015Exterior lighting. Supersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision.
• 10120003Apr 17, 2015Exterior lighting. Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
• 10120014Apr 7, 2015Electrical system, Engine cooling. The vehicle's engine management software has been improved to assure the vehicle's tailpipe emissions are optimized and operating efficiently. Under certain operating conditions, the earlier strategy may have increased the chance of the vehicle's MIL light illuminating. If the MIL illuminates for any reason, the vehicle will not pass an IM emissions inspection in some regions. ECM software update needed.
• 10119999Apr 7, 2015Seats. Supersedes Technical Service Bulletin Group 74 number 14-19 dated May 9, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damaged is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. This occurs when the rear seat is folded down with the headrests installed, and the front seat is moved…
• 10120016Apr 6, 2015Engine cooling. This document contains information about the upcoming emissions service action 23N4.
• 10120679Mar 24, 2015Equipment. Supersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate-length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the…
• 10119956Mar 20, 2015Electrical system. Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type…
• 10119945Mar 17, 2015Engine cooling. Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust…
• 10119955Mar 10, 2015Equipment. Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
• 10119940Mar 9, 2015Fuel system. Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle…
• 10119946Mar 6, 2015Engine cooling. Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
• 10120700Feb 26, 2015Steering. Supersedes Technical Service Bulletin Group 48 number 13-37 dated February 28, 2013. Steering feels stiff after engine start on vehicles with generation 3 steering. DTCs may be stored in the power steering control module.
• 10057683Feb 26, 2015Steering, Electrical system. Audi: some vehicles an incorrect software installed, causing the steering to be stiff after engine has started. Model 2009-13 a3, tt.
• 10120704Feb 23, 2015Equipment. Supersedes Technical Service Bulletin Group 28 number 11-18 dated November 9, 2011. Radio turns on and off while vehicle is being driven. Clock in radio sporadically does not work. Door locks actuate while vehicle is being driven. There is a sporadic disruption of S-contact due to lubricant on the contact surface.
• 10120682Feb 13, 2015Engine cooling. Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
• 10119854Jan 16, 2015Electrical system, Fuel system. The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. This issue is related to the diesel fuel and not a technical problem with the vehicle.
• 10231116Dec 22, 2014Equipment. Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
• 10124893Dec 19, 2014Equipment. Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
• 10228302Dec 10, 2014Equipment. High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
• 10224981Dec 10, 2014Electrical system, Equipment. High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
• 10221954Dec 10, 2014Equipment. High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
• 10124882Dec 10, 2014Electrical system. High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
• 10250944Dec 8, 2014Steering. Steering wheel shimmy, vibration, and/or oscillation
• 10231114Dec 8, 2014Equipment. Technical bulletins and updates
• 10124892Dec 8, 2014Equipment. Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected.

← All problems reported for the 2013 Audi A3