2013 Audi A3 Technical Service Bulletins

864 technical service bulletins (TSBs) are on record for the 2013 Audi A3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10221949Jul 15, 2014Equipment. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
• 10122522Jul 15, 2014Electrical system. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
• 10250966Jul 14, 2014Brakes. Brake pulsation diagnostic guidelines
• 10231125Jul 14, 2014Equipment. Pending service solutions and bulletins
• 10128242Jul 14, 2014Suspension, Brakes, Air bags. Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations.
• 10249055Jul 10, 2014Other or unknown, Fuel system. Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
• 10249054Jul 10, 2014Other or unknown. Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
• 10122576Jul 10, 2014Fuel system. This document modifies the Audi Warranty Policies and Procedures Manual applicable to engine codes CBEA, CATA, CNRB, CPNA, CPNB: 2009-2015 model year TDI® clean diesel vehicles using biodiesel blended fuels - registered in the state of Minnesota only.
• 10122563Jul 10, 2014Equipment. Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises.
• 10250963Jul 9, 2014Steering. Loud cracking or rubbing noises when steering (vehicles without Audi magnetic ride suspension)
• 10250673Jul 9, 2014Steering. Loud cracking or rubbing noises when steering (vehicles without Audi magnetic ride suspension)
• 10122542Jul 9, 2014Steering. Supersedes Technical Service Bulletin Group 42 number 12-16 dated November 13, 2012. Loud cracking or rubbing noises are heard when the steering wheel is being turned. Steering is not affected and operates normally. This bulletin does not apply to vehicles with magnetic ride suspension (which are equipped with rubber shock absorber stop and a plastic cap on the shock).
• 10066027Jul 9, 2014Suspension. Summary to be provided on a future date.
• 10250959Jul 2, 2014Suspension. Shock absorber leaks: assessment aid
• 10250958Jul 2, 2014Steering. Squeaking noises when steering or maneuvering
• 10250665Jul 2, 2014Body and structure, Equipment. Shock absorber leaks: assessment aid
• 10250664Jul 2, 2014Steering. Squeaking noises when steering or maneuvering
• 10122540Jul 2, 2014Suspension. Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
• 10122539Jul 2, 2014Steering. Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the…
• 10231130Jun 30, 2014Engine cooling. Idenifying and mixing factory fill engine coolants
• 10122415Jun 20, 2014Engine cooling. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
• 10231127Jun 9, 2014Equipment, Electrical system. ElsaPro Software update and technical bulletins
• 10212703May 29, 2014Transmission and drivetrain. Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
• 10228295May 28, 2014Engine cooling. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10226529May 28, 2014Transmission and drivetrain. Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
• 10224974May 28, 2014Engine cooling. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10221947May 28, 2014Engine cooling. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10210679May 28, 2014Electronic stability control, Transmission and drivetrain. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system…
• 10122465May 28, 2014Transmission and drivetrain. Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left…
• 10122452May 28, 2014Engine, Equipment. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating…
• 10231139May 26, 2014Equipment. Technical bulletins and updates
• 10250971May 14, 2014Steering. Steering wheel shimmy, vibration, and/or oscillation
• 10122467May 14, 2014Suspension, Steering. Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair…
• 10249085May 13, 2014Other or unknown. Google Maps Street View (NVLW))
• 10122474May 9, 2014Seats. Supersedes Technical Service Bulletin Group 74 number 14-18 dated February 26, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damaged is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. This occurs when the rear seat is folded down with the headrests installed, and the front seat is…
• 10122360Apr 21, 2014Equipment. Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple® devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi…
• 10250982Apr 17, 2014Steering. Steering wheel shimmy, vibration, and/or oscillation
• 10122338Apr 17, 2014Suspension. Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair…
• 10250106Apr 14, 2014Equipment. Elsa newsletter
• 10122359Apr 10, 2014Electrical system, Equipment. Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating…
• 10122357Apr 8, 2014Equipment. Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
• 10231131Apr 3, 2014Equipment. Technical bulletins and updates
• 10216651Apr 3, 2014Back-over prevention (rear camera). The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period…
• 10122332Apr 3, 2014Electrical system. Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for…
• 10249053Apr 2, 2014Engine cooling, Other or unknown. AC Pressure/Temperature Sensor
• 10226656Apr 2, 2014Equipment. Audi Minimum Required Tool Package Shipment AT-357
• 10122379Apr 2, 2014Equipment. This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off.
• 10231135Mar 31, 2014Equipment. Technical bulletins and updates
• 10122295Mar 31, 2014Air bags. Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when…
• 10216612Mar 20, 2014Steering, Brakes, Fuel system. When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump.

← All problems reported for the 2013 Audi A3