2015 Audi Q7 Technical Service Bulletins

904 technical service bulletins (TSBs) are on record for the 2015 Audi Q7. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10124709Oct 22, 2015Equipment. This document contains the Audi vehicle condition report checklist.
• 10123716Oct 20, 2015Steering, Brakes. Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental…
• 10123726Oct 15, 2015Back-over prevention (rear camera). Supersedes Technical Service Bulletin Group 91 number 15-04 dated July 22, 2015. The customer complains that the rearview camera image is not displayed on the MMI display. DTC 02203 (audio/video input 1) is logged in the rearview camera system control module. An issue with the wiring harness may cause the condition.
• 10123721Oct 14, 2015Visibility (wipers, defrost, mirrors). Supersedes Technical Service Bulletin Group 70 number 15-47 dated September 21, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
• 10123714Oct 13, 2015Brakes. Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. DO NOT use this TSB if there is another brake noise TSB applicable to the VIN. For additional information, refer to the Audi Brake systems brochure. Brake noise…
• 10123712Oct 5, 2015Suspension. Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair…
• 10123717Oct 2, 2015Equipment. Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing.
• 10123754Oct 1, 2015Equipment. This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Thereafter, all remaining scheduled services are due every 10,000 miles or 1 year after previous service, whichever occurs first.
• 10123774Sep 29, 2015Electrical system. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM…
• 10123773Sep 29, 2015Back-over prevention (rear camera). Supersedes Technical Service Bulletin Group 91 number 14-70 dated November 6, 2014. The overhead view camera system or one of its cameras does not work. DTCs are logged in the rearview camera system control module. DTCS for the affected camera may also be logged. Incorrect component.
• 10123771Sep 24, 2015Equipment. Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is…
• 10123792Sep 21, 2015Equipment. This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
• 10123775Sep 21, 2015Electrical system. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener…
• 10123770Sep 21, 2015Visibility (wipers, defrost, mirrors). Supersedes Technical Service Bulletin Group 70 number 15-44 dated February 25, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
• 10123769Sep 15, 2015Electrical system. Supersedes Technical Service Bulletin Group 48 number 14-62 dated September 23, 2014. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable…
• 10074502Sep 15, 2015Electrical system, Steering. Summary to be provided on a future date.
• 10123763Sep 9, 2015Engine. Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
• 10123764Sep 8, 2015Engine cooling. Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
• 10123760Sep 3, 2015Electrical system. DTCs are stored in the ECM. There may be soot buildup on the moveable elements of the pressure sensing glow plug (PSG).
• 10128419Aug 28, 2015Equipment. Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
• 10128415Aug 27, 2015Equipment. Supersedes Technical Service Bulletin Group 91 number 15-80 dated March 20, 2015. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user?s myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice…
• 10128408Aug 19, 2015Equipment. Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
• 10128400Aug 4, 2015Electrical system. DTC P103200 (NOx sensor signal too high) is stored in the engine control module (ECM). Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts.
• 10058587Jul 22, 2015Back-over prevention (rear camera). Audi: some vehicles experience, intermittently, the mmi display failing to display rearview camera image due to possible wiring harness issue. Model 2013-16 a4, a5, a8, q3, q5, q7.
• 10128399Jul 7, 2015Engine cooling. Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
• 10128471Jul 1, 2015Transmission and drivetrain, Equipment. Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in…
• 10058584Jul 1, 2015Engine. Audi: engine, on some vehicles, would run irregularly or have malfunction indicator lamp (mil) on or possible filter element for camshaft adjustment valve can loosen and in oil circuit, there is no damage from loosened particles. Model all. All years.
• 10120811Jun 30, 2015Fuel system. Supersedes Technical Service Bulletin Group 01 number 14-75 dated March 20, 2014. The MIL is on. No start or rough running. One or more DTCs are stored in the engine control module. When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for…
• 10058586Jun 30, 2015Engine cooling. Audi: some vehicles will experience rough running or a no start condition with malfunction indicator lamp (mil) on and may need checking high pressure fuel pump for metallic particles. Model 2013-2016 a3, a8, q5, 17.
• 10120832Jun 29, 2015Electrical system. Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises.
• 10120821Jun 24, 2015Equipment. Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
• 10120829Jun 19, 2015Electrical system. The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
• 10120744Jun 19, 2015Equipment. Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
• 10120828Jun 16, 2015Equipment. Supersedes Technical Service Bulletin Group 91 number 15-84 dated May 14, 2015. During PDI, the Navigation function is found to not be available. The error message ?Navigation data is invalid? appears in the MMI. During a certain production period, the supplier of the MMI main unit incorrectly configured the software for the MMI. As a result, Navigation cannot be activated.
• 10120929Jun 15, 2015Transmission and drivetrain, Steering, Engine, Brakes, Equipment. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service.
• 10120743Jun 9, 2015Engine cooling. The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM.
• 10120805Jun 2, 2015Engine. Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
• 10120052May 29, 2015Electrical system. Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
• 10120048May 19, 2015Equipment. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded.
• 10120041May 18, 2015Equipment. Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
• 10120045May 14, 2015Equipment, Electrical system. During PDI, the Navigation function is found to not be available. The error message "Navigation data is invalid" appears in the MMI. During a certain production period, the supplier of the MMI main unit, Harman, incorrectly configured the software for the MMI. As a result, Navigation cannot be activated.
• 10120042May 11, 2015Steering, Equipment. Customer reports that the ignition sporadically cannot be switched on. DTC 00456 (Access/start control module -J518- no communication) is found in several control modules or the access/start authorization control module, J518 (address word 05), identifies itself with implausible data can be found through guided fault finding (GFF). If no communication is possible, activate the bus by switching on the hazard warning…
• 10120043May 8, 2015Equipment, Electrical system. Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814.
• 10120051May 6, 2015Electrical system. Supersedes Technical Service Bulletin Group 97 number 13-40 dated November 26, 2013. The customer may report multiple warning lights are/were illuminated simultaneously. The warning lights may be sporadic, and may not be illuminated when the customer brings the vehicle to the workshop. CAN communication DTCs may be found in control modules. There is sporadic data disruption on the CAN bus wiring behind the…
• 10058581May 6, 2015Equipment. Audi: some vehicles experience simultaneously warning illumination and at other times warning illumination is sporadic or not at all on engine, transmission, airbag, tpms, suspension. Model 2010-15 q7.
• 10120049May 1, 2015Visibility (wipers, defrost, mirrors). Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the…
• 10119997Apr 30, 2015Body and structure. Supersedes Technical Service Bulletin Group 66 number 15-50 dated April 10, 2015. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors.
• 10119990Apr 28, 2015Transmission and drivetrain. Supersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold (normally below freezing) and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
• 10120002Apr 24, 2015Back-over prevention (rear camera), Equipment. Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off.
• 10120003Apr 17, 2015Exterior lighting. Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.

← All problems reported for the 2015 Audi Q7