2014 BMW 550I Technical Service Bulletins

393 technical service bulletins (TSBs) are on record for the 2014 BMW 550I. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10148227Aug 1, 2014Equipment, Body and structure, Latches, locks and linkages. Rattling Noise from Mid-range Speaker in Front Door Panel. The customer complains of a rattle noise in either the left or right front door only when the speakers are in use. The inside door lock rod is making contact with the inside panel when the speakers are in use at certain volume and frequency levels.
• 10148226Aug 1, 2014Equipment. Bang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly.
• 10148218Aug 1, 2014Fuel system. N20 and N26 Injector Replacement. INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this…
• 10148215Aug 1, 2014Equipment. BMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns…
• 10148135Jul 1, 2014Electrical system. ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical…
• 10148132Jul 1, 2014Forward collision avoidance. Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller.
• 10148130Jul 1, 2014Electrical system, Seats. When Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
• 10148129Jul 1, 2014Equipment. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue.
• 10148128Jul 1, 2014Equipment. Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
• 10148120Jul 1, 2014Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.
• 10148118Jul 1, 2014Equipment. Service Action: Replace Center Console Lock Cylinder. The center console lock cylinder is loose. Manufacturing tolerances of the center console lock cover cap may cause it to become loose or missing. AFFECTED VEHICLES This Service Action involves F01, F02, F06, F07, F12 and F13 vehicles produced from March 7, 2014 to April 23, 2014. First check if a Service Action label with a code number 688 is already attached to…
• 10148101Jun 1, 2014Electrical system. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
• 10148333May 1, 2014Electrical system, Engine. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
• 10148315May 1, 2014Brakes. Incorrect Remaining Service Life from CBS Data for Brake Pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software…
• 10148313May 1, 2014Equipment, Steering. Service Action: Replace Power Steering Pump Belt Pulley. The screw connection on the power steering pump belt pulley may slacken. This may lead to an audible squeaking and rattling at the pulley drive. AFFECTED VEHICLES This Service Action involves 5 Series 535d vehicles according to VIN selection. First check if a Service Action label with a code number 682 is already attached to the B-pillar.
• 10148312May 1, 2014Suspension. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
• 10148308May 1, 2014Fuel system. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or…
• 10148276Apr 1, 2014Equipment. Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
• 10148273Apr 1, 2014Equipment, Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.
• 10148258Apr 1, 2014Engine, Fuel system. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or…
• 10148256Apr 1, 2014Transmission and drivetrain, Engine. N52T / N55 with 8HP45: Delay in Engine Response. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
• 10148010Mar 1, 2014Equipment, Electrical system. ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive.
• 10147923Mar 1, 2014Electrical system. """Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
• 10147921Mar 1, 2014Wheels. Fitting Winter Tires Properly to Vehicles with Ceramic Brakes. Wheel studs may loosen after wheels for the rear axle are incorrectly fitted to the front axle on vehicles equipped with option 2NK (ceramic brakes). Incorrect installation of rear axle winter tires (wheel style 409M) onto the front axle in conjunction with ceramic brakes
• 10147918Mar 1, 2014Engine. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION There is an error in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. The vehicle may also exhibit…
• 10147985Feb 1, 2014Electrical system. My BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
• 10147984Feb 1, 2014Equipment. iPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
• 10147982Feb 1, 2014Equipment. Headunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
• 10147981Feb 1, 2014Air bags. "Airbag Warning Light: ACSM FC 930A60 Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a…
• 10147976Feb 1, 2014Electrical system. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
• 10147954Jan 1, 2014Equipment. Enabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
• 10147953Jan 1, 2014Electrical system. "ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is…
• 10147952Jan 1, 2014Electrical system. Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code…
• 10147946Jan 1, 2014Electrical system, Exterior lighting. "Adaptive Headlight Malfunction in Cold Weather. * In very cold weather conditions (32ºF or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is…
• 10147945Jan 1, 2014Exterior lighting. Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
• 10147706Jan 1, 2014Engine. ?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME.
• 10150185Nov 1, 2013Equipment, Electrical system. Touchpad Integrated in the iDrive Controller Is Intermittently Inoperative. Intermittently the Touchpad integrated in the iDrive controller is inoperative. * No entries can be made using the Touchpad * Fault code is stored in the touch-box control unit Software error in the touch-box control unit (TBX)
• 10150183Nov 1, 2013Exterior lighting, Electrical system. Daytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
• 10150181Nov 1, 2013Transmission and drivetrain, Electrical system. """Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
• 10150171Nov 1, 2013Equipment. Bang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly
• 10150166Nov 1, 2013Brakes. Incorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model.
• 10150163Nov 1, 2013Electrical system, Engine. ?Service Action: Program Control Units (Oil Level Sensor). Due to a signal error from the oil level sensor, the vehicle could display an erroneous message indicating that an oil service is due after only a short distance has been traveled.
• 10150162Nov 1, 2013Electrical system, Engine. N63: Service Engine Soon Lamp (MIL) Is On with Fault 1D2008 Stored. Under certain low-load driving conditions at low outside ambient temperatures, the following fault may be stored in the DME with the Service Engine Soon lamp (MIL) on: Fault 1D2008 - Map thermostat, mechanical: jammed open. However, the thermostat is found to be operating correctly with sufficient heat output from the climate control system, and…
• 10150161Nov 1, 2013Engine, Transmission and drivetrain. N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised…
• 10150266Oct 1, 2013Seats. Installation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
• 10150263Oct 1, 2013Equipment. "IHKA Operating Panel Buttons Are Peeling. INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the ""Repair kit for button caps"" when performing this repair. Replace ALL the buttons with those included in the kit.
• 10150257Oct 1, 2013Fuel system. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or…
• 10150256Oct 1, 2013Fuel system. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME.
• 10150254Oct 1, 2013Fuel system. "N63T: Drive Malfunction Message with Rail Pressure Sensor Fault Stored. The Check Control Message ""Drive, drive moderately"" is displayed with any of the following rail pressure sensor faults stored in the DME: 119001 - Rail pressure sensor, electrical: Short circuit to positive 119002 - Rail pressure sensor, electrical: Short circuit to ground 119101 - Rail pressure sensor 2, electrical: Short circuit to…
• 10150253Oct 1, 2013Engine cooling. N63T Engine: New Test Plan to Check Engine Oil Level with ISTA/D 3.39.21. INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up.

← All problems reported for the 2014 BMW 550I