2024 Mercedes-Benz C300 Technical Service Bulletins

314 technical service bulletins (TSBs) are on record for the 2024 Mercedes-Benz C300. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 11020009Jun 12, 2025Electrical system, Engine. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control software might not meet current specifications. As a result, the diagnosis routine for monitoring the air-fuel ratio might not be activated as intended and a malfunction in the oxygen sensor could be erroneously detected causing the “check engine” Malfunction Indicator Lamp (‘MIL’) to…
• 11019747Jun 9, 2025Steering. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2.
• 11019016May 30, 2025Electrical system, Fuel system. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage detection (“DMTL”) on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle…
• 11018714May 30, 2025Electrical system. Complaint The following most common complaints may be observed: • Brief connectivity interruptions when using Apple CarPlay over Wi-Fi • Audio cuts out • Device not recognized • No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicle’s head unit while using Apple CarPlay.
• 11018701May 29, 2025Seats. Complaint Squeaking or creaking noises on uneven roadways, in turns, or when moving in their seat. Cause Noise in the backrest adjustment mechanism Remedy The adjustment mechanism is treated with dry lubricant spray A000 989 35 60 to rectify the noise. To do this, proceed as follows: • Move the seat to the front position and put the backrest into a lying position. • Due to the risk of soiling on the left and right…
• 11019018May 21, 2025Transmission and drivetrain. Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner…
• 11018365May 14, 2025Exterior lighting. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause HLI control units processing of level sensor data. Remedy Update the software for the HLI control units - starting with the left…
• 11018297May 13, 2025Exterior lighting. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause HLI control units processing of level sensor data. Remedy Update the software for the HLI control units - starting with the left (driver…
• 11018627May 10, 2025Engine. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the ME-SFI control unit software does not meet current production specifications. As a result, a check engine malfunction indicator lamp might erroneously be triggered.
• 11018164May 7, 2025Electrical system. Complaint Please note that the exact quick test conditions must be met as seen below. If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document.
• 11018160May 7, 2025Electrical system. Complaint After the charging process is complete, the IC message with charging error appears and the FC P0CFE00 is stored in the "N83 - AC charger for high-voltage battery (SG-LG)" control unit. The fault message and the fault memory entry can also appear during time-delayed charging at the start of the pause in charging. Both only occur in combination with active pre-entry climate control. Cause Software in the…
• 11018031May 5, 2025Electrical system. Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: Perform SCN coding in control unit OMSH223 (N168). For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be…
• 11018890May 3, 2025Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the ignition lock (EZS) control unit does not correspond with the latest series production configuration. The EZS control unit will receive an OTA software update which will improve the performance of hands-free access on the affected vehicles. MBUSA will conduct an OTA service campaign.
• 11018206May 2, 2025Electrical system. Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged…
• 11018204May 2, 2025Forward collision avoidance, Steering, Lane departure. Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness.
• 11018039May 1, 2025Electrical system. Complaint Symptoms relating to CIVIC A26/17 - MBUX multimedia system + instrument cluster (head unit)] and/or displays Cause Enhanced technical support process for CIVIC modules and associated displays Remedy Note: Do not replace any components. For all symptoms concerning CIVIC and displays create a TIPS case after performing initial diagnosis.
• 11018032May 1, 2025Electrical system. Complaint In vehicles with the MBUX multimedia system Gen20x.i2 without premium sound system and external amplifier, the sound does not meet the customer's expectations. Changing the sound settings, for example for the bass, does not provide the desired effect. Cause Sound parameter software in the A26/17 - MBUX multimedia system + Instrument cluster (Head unit) control unit Remedy For vehicles with standard sound…
• 11017500Apr 28, 2025Exterior lighting. Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged…
• 11017496Apr 28, 2025Exterior lighting. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear…
• 11017218Apr 25, 2025Air bags, Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the airbag control unit software does not correspond to the latest series production configuration. The airbag control unit will be updated to improve the vehicle charging functionality during future OTA updates. MBUSA will conduct an OTA service campaign.
• 11017217Apr 21, 2025Visibility (wipers, defrost, mirrors). Complaint Random heating of air conditioning system. Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored).
• 11017208Apr 21, 2025Electrical system, Exterior lighting. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the control unit HLI/LED headlamp range adjustment front left. Cause Electronic interference occurring at the sensor level of the front axle. Remedy Update of the…
• 11017127Apr 21, 2025Seats, Electrical system. Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available.
• 11017220Apr 17, 2025Engine, Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software may not correspond with current production specifications. There is a possibility that the dynamic driving profile may not be accurately calculated, which could possibly lead to an unsuccessful diagnostic routine for the lambda sensors. MBUSA will conduct a service…
• 11017078Apr 17, 2025Engine, Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software does not correspond to current production specifications. The diagnosis routine for the pressure sensor in the crankcase ventilation system may be populated with incorrect data. As a consequence, the check engine light may illuminate after the engine is switched off even…
• 11017516Apr 11, 2025Electrical system, Steering. Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data.
• 11017037Apr 7, 2025Electrical system. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off…
• 11016043Mar 24, 2025Transmission and drivetrain. Complaint A clicking/ticking/taping noise from underneath the vehicle with engine off during ECO stop event or after parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps.
• 11016038Mar 21, 2025Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the software for the airbag control unit does not correspond to the latest series production configuration. The airbag control unit will be updated to improve the vehicle charging functionality during future OTA updates. MBUSA will conduct an OTA service campaign.
• 11015626Mar 13, 2025Electrical system, Transmission and drivetrain. Complaint - Engine diagnosis indicator lamp (MIL) lights up. - Current and saved fault code in DCCU and powertrain control unit (PTCU): P2E9873 The position sensor of the external socket flap of the vehicle socket (direct current) indicates an electrical fault. The actuator does not open. - The vehicle starts or charges normally and without any problems. Cause Software in the control unit "N116/5 - DC…
• 11015627Mar 10, 2025Electrical system, Exterior lighting. Complaint The luggage compartment lighting switches off and back on erratically if the tailgate is opened with the ignition switched off. Cause The problem was caused by a software error in the control unit N10/8 (Rear SAM). Remedy Software update to the control unit N10/8 (Rear SAM - Signal acquisition and actuation module rear control unit).
• 11015617Mar 10, 2025Electrical system, Body and structure. Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button…
• 11015614Mar 10, 2025Suspension. Complaint A squeaking noise comes from the electric power steering; see video with example. Cause Toothed rack in the area of the screw drive of the electric power steering needs additional grease. Remedy 1. Lift the vehicle and remove the center engine compartment lining; for basic data, see WIS AR61.20-P-1105S 2. Loosen the bellows of the electric power steering on the right of the steering gear and slide outward…
• 11015667Mar 8, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles. The software for the communication module does not correspond to the latest series production configuration. The communication module will receive an OTA update. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new…
• 11015663Mar 7, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and…
• 11015659Mar 7, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and…
• 11015543Mar 7, 2025Engine. Complaint Check engine light on. Engine in limp-home mode. Rough running. Low fuel rail pressure fault code P008700 stored in MRG2 control unit. Additional faults below may be stored in MRG2 control unit: Misfire- P030000, P030100, P030200, P030300, P030400, P030084, P030004 Mixture adaptation- P217800 P218762, P017100, P017200, P217700 Injector malfunction- P02EE00, P02EF00, P02F000, P02F100, P214601, P214901…
• 11015673Mar 5, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the MBUX multimedia system software does not correspond with the latest series production configuration. The MBUX multimedia system software will receive an update to introduce new functions and improve the customer experience. Remedy MBUSA will conduct an OTA service campaign.
• 11015640Mar 5, 2025Electrical system. Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21)…
• 11014686Feb 28, 2025Fuel system. Complaint Check engine light on. Engine in limp-home mode. Rough running. Low fuel rail pressure fault code P008700 stored in MRG2 control unit. Additional faults below may be stored in MRG2 control unit: Misfire- P030000, P030100, P030200, P030300, P030400, P030084, P030004 Mixture adaptation- P217800 P218762, P017100, P017200, P217700 Injector malfunction- P02EE00, P02EF00, P02F000, P02F100, P214601, P214901…
• 11014684Feb 28, 2025Engine. Complaint Red oil pressure warning in instrument cluster One of the below fault codes is stored in powertrain control unit N127: P052497 The oil pressure is too low. The system function is restricted. P052400 The oil pressure is too low Cause Various Remedy If low oil level warning present diagnose cause of this first. -Check engine oil level and correct if necessary.
• 11014610Feb 25, 2025Back-over prevention (rear camera), Electrical system. Complaint Please note that the exact quick test conditions must be met as seen below. If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document.
• 11014402Feb 21, 2025Fuel system. Complaint Customer-perceived problem: • Fuel gauge reading implausible • MIL ON (market-dependent) N118/3 Fault codes in control units FSCM_GEN4/5/6 • For these fault codes, the tests contained in XENTRY must be carried out P046109 / P206609 / P13E600 • For these fault codes, the connector couplings/wiring harness routing must be checked for damage P206600 / P046100 Cause Various Remedy Carry out XENTRY tests for…
• 11014398Feb 20, 2025Other or unknown. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference.
• 11014399Feb 19, 2025Engine. Complaint Engine idle fluctuates or stumbles at approximately 7 second interval. No relevant fault codes are stored. If fault codes are stored or check engine light illuminated, this should be diagnosed separately. Cause Torque signal mismatch between MRG and PTCU control units. Only effects version 20B of PTCU. Remedy Software solution in development and LI will be updated once an ETA is available. Replacing parts…
• 11014255Feb 12, 2025Electrical system, Visibility (wipers, defrost, mirrors). Complaint Please note that the exact quick test conditions must be met as seen below. If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document. Conditions Instrument Cluster Message: "Park Assist Inoperative" and B223263 with Bosch-ID C259; A+S (Active and Stored) and B223255 with Bosch-ID 1B5D; A+S (Active and Stored)…
• 11014223Feb 6, 2025Engine. Complaint Red cooling system malfunction warning due to overheat. Low engine performance. Check engine light on. Fault codes may be stored: P21814B The cooling system has a malfunction. There is a fault due to overtemperature. P2B8500 The rpm of the coolant pump is too low. Cause Various Remedy Check for loose plug at electrical connectors of high temp coolant pump (M43/10 or M75/11) by gently pulling on connector…
• 11014412Feb 3, 2025Brakes. Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and…
• 11013996Feb 3, 2025Electrical system, Forward collision avoidance, Lane departure. Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data.
• 11013297Jan 31, 2025Transmission and drivetrain, Electrical system. Complaint • Hard 1-2 shift • Jerky shifting • Jolting when moving off Cause Insufficient data points for the adaptation limits algorithm Remedy Problem will be rectified with a new SW release Until the SW release is available, (No current ETA) please carry out the following: • Check the transmission oil level and correct if necessary • Rinse the valves a minimum of 3 times via XENTRY • Perform a stationary…

← All problems reported for the 2024 Mercedes-Benz C300